Nov 19, 2026 Leave a message

Custom Automotive Ethernet Cable Assemblies: From Connector Selection to Production

Introduction :

 

A custom automotive Ethernet cable assembly must match the electrical, mechanical, and environmental requirements of the vehicle network. Selecting the right connector is only the starting point. Cable construction, connector coding, shielding, cable length, sealing, and production inspection all affect the reliability of the finished assembly.

 

For automotive engineers and purchasing teams, understanding these factors helps avoid connector mismatches, installation problems, and unnecessary redesigns. This guide explains the key steps involved in specifying and manufacturing custom automotive Ethernet cable assemblies, using the TE MATEnet 1802113-9 waterproof cable assembly as a practical example.

 

 

Selecting the Right Automotive Ethernet Connecto 

Before selecting a connector, the following information needs to be confirmed:

 

 

  • Connector series and mating interfaces
  • Male or female contact configuration
  • Coding and polarization (poka yoke) requirements
  • Number of ports
  • Cable exit direction
  • Sealing and mounting requirements

 

MATEnet is a compact automotive Ethernet connector system developed by TE Connectivity, designed specifically for in vehicle data communication. Its various keying configurations help distinguish between different connection interfaces and prevent the mis mating of incompatible connectors.


A representative option is the TE Connectivity 1802113-9, a sealed, single port MATEnet receptacle housing with Z Code identification. It supports cable to board and cable to cable configurations and features a 180 degree cable exit.


For a double ended cable assembly, both connector ends can use TE 1802113-9 receptacle housings. The mating equipment must have the corresponding compatible MATEnet Z Code interface.


Choosing the correct connector at the beginning helps ensure mechanical compatibility and simplifies subsequent cable assembly development.

1802105-9
MATEnet Cable Assembly

 

Choosing the Appropriate Automotive Ethernet Cable

The cable must match the connector configuration and the electrical requirements of the communication system.Two common cable constructions are:

 

  • Shielded Twisted Pair (STP)

STP cables incorporate shielding to help control electromagnetic interference in electrically demanding environments. They are commonly considered for automotive Ethernet installations where the shielding design and grounding strategy are part of the system requirements.

 

  • Unshielded Twisted Pair (UTP)

UTP cables do not incorporate the same cable shielding structure. They may be appropriate for applications designed around an unshielded Ethernet channel.

 

Connector compatibility alone does not mean STP and UTP assemblies are interchangeable. The cable, connector configuration, and shielding termination must be selected together.

 

For example, the TE 1802113-9 is intended for STP cable configurations, while TE 1802105-9 is an alternative used for UTP applications.

 

 

Premier Cable Product Showcase

Automotive Ethernet STP Cable
TE MATEnet 1802113-9 Cable Assembly
MATEnet Cable Assembly
Waterproof MATEnet Cable

Considering Waterproofing and Mechanical Requirements

Automotive cable assemblies may be installed in locations exposed to moisture, temperature changes, vibration, and limited installation space.

 

Several mechanical details should be confirmed during the design stage:

 

  • Cable length and installation route
  • Connector orientation and cable exit direction
  • Available clearance around the mating interface
  • Cable bending requirements
  • Sealing requirements at the connection point
  • Shielding and cable termination arrangements
  •  

The TE 1802113-9 features a sealed connector housing and a straight 180-degree cable exit. The featured Premier Cable assembly specifies IP67 connector protection when properly mated. Its specified operating temperature range is -40°C to +105°C.

 

One important consideration is that connector protection depends on proper mating. The protection level of the complete installed system must also account for the mating connector, cable interface, and installation conditions.These details should be confirmed before production, particularly when the assembly will be installed in exposed vehicle areas or demanding industrial environments.

 

 Define requirements for custom cable assemblies

A complete specification for a cable assembly should clearly define the following:

 

  • Connector A and Connector B part numbers
  • Connector coding and contact configuration
  • Cable manufacturer and cable model
  • Cable type and nominal impedance
  • Required cable length
  • Shielding and termination requirements
  • Connector protection requirements
  • Wiring configuration and applicable drawings
1802113-9

 

 

Custom Automotive Ethernet Cable Solutions from Premier Cable

Premier Cable provides custom automotive Ethernet cable assemblies using TE MATEnet connectors and automotive Ethernet cables, including LEONI DACAR series options.

 

From connector selection and cable configuration to customized lengths, shielding termination, prototype development, and volume production, each project can be specified around its intended application.

 

For your next automotive Ethernet project, contact Premier Cable with your connector part numbers, cable requirements, drawings, and estimated order quantity.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry